See Availability

 

 

How do you actually feel on the subject of Installing A Bathtub?

Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately challenging task. If the old bathtub is readily accessible, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have actually qualified yourself for the job and are comfortable attempting it. Instead of employing a contractor to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already bought a brand-new tub as well as do not require to change the setup of your previous water pipelines.
Your tools and also product checklist need to consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Planning for the Installation

To start with, the supporting frame provided with the bath should be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent pressure on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing taps can be rather problematic due to the limited access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

 

 

Setting up the Tub

Making use of both wooden boards under its feet, put the tub in the called for position. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub up until the spirit level reads degree.
To mount taps, fit all-time low of the outermost versatile faucet port to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Activate the supply of water as well as examine all joints and new pipework for leaks and tighten them if required. Fill up the tub as well as additionally examine the overflow outlet as well as the normal electrical outlet for leakages.
Ultimately, fix the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the tub must wait up until the bath tub has actually been used a minimum of once as this will certainly resolve it into its last setting.

 

 

Suitable New Touches

If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type needs to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Tub

In the location where the bathroom meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, bring about issues with dampness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bath tub with water prior to securing, to allow for the activity experienced when the tub is in use. The sealer can split fairly very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the market. It is a good idea to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you enjoy reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Create feedback below. We'd be delighted to listen to your opinions about this write-up. Hoping that you visit us again later on. Those who appreciated our article kindly make sure you remember to pass it around. I am grateful for your time. Come back soon.

Call Today